Wednesday, October 1, 2008

Funny Things To Write In A Guest Book

RAM Memory Chips


Celeron microprocessor

Celeron processors can perform the same basic functions as other processors, but its performance is inferior when compared to other more expensive processors. For example, the Celeron usually have less cache, or have some advanced features disabled.


Features:


-Production: April 1998
-Manufacturer: Intel CPU
-speed: 266 MHz 3.6 GHz-speed
FSB : 66 MT / s to 800 MT / s
-Process (channel length MOSFET ) 0.25 microns to 0,065 microns








Pentium microprocessor


The October 19, 1992, Intel announced that the fifth generation of its compatible processor line (which was the internal code P5) would be named Pentium rather than 586 or 80586, as everyone was expecting. This was one Intel strategy to register the mark and thus can differ the name of their processors of its competitors (primarily AMD and Cyrix).
This chip was submitted on March 22, 1993

FEATURES:


-Initial rates of 60 and 66 MHz
-Manufactured with the process BICMOS (Bipolar-CMOS) of 0.8 microns)
-memory cache of 8 KB for data

-8 KB instruction data bus 64-bit
"The chip is packaged in PGA (Pin Grid Array) of 273 pins.
"The Pentium processor is modeled 386/486







Intel Pentium II


The Pentium II is a microprocessor designed by Intel, introduced in the market in May 1997 7DE fundamental changes compared to the latter were to improve performance code execution 16 bits, eliminating the second-level cache processor core, placing it in a printed circuit board next to it.


Features:


-Production: From mid-1997 until early 1999
-Manufacturer: Intel deCPU
-Speed: 233 Mhz to 450 Mhz
- fsb speed: 66 MHz to 100 MHz
-Process (channel length MOSFET ) 0.35 microns to 0.25 microns
-Chip: P6







Intel Pentium III


was released on February 26, 1999.
The first versions were very similar to the Pentium II, the major difference being the introduction of SSE instructions. As with the Pentium II.


Features:


-production: From 1999 to 2003
-Manufacturer: Intel CPU
-speed: 450 MHz to 1.4
-GHz FSB Speed: 100 MHz to 133 MHz
- Process: (MOSFET channel length) 0.25 microns to 0.13 microns






Intel Pentium 4


The Pentium 4 is a seventh-generation microprocessor chip is the first with a completely new design. The original Pentium 4, called Willamette, working at 1.4 and 1.5 GHz, and was released in November 200.
To the surprise of the computer industry, the Pentium 4 is not the old design improved P6 according to the two traditional ways to measure performance: speed in the process of integers or floating point operations. Intel's strategy


Features:


-production: From 2000 to 2008
-Manufacturer: Intel

-speed CPU: 1.3 GHz to 3.8 GHz
-Process (channel length MOSFET ) 0.18 microns to 0,065 microns
-Microarchitecture, NetBurst




Intel Core Duo


A sixth-generation microprocessor launched in January 2006 by Intel with two execution cores, optimized for multithreaded applications and multitasking. You can run multiple demanding applications simultaneously such as graphics-intensive games or programs that require many calculations, while you can download music or analyze your PC with your antivirus


Features:


-Production: From 2006 to 2008
-Manufacturer: Intel
-CPU Speed: 1.06GHz to 2.33 GHz-speed
FSB 533 MT / s to 667 MT / s
-Process (channel length MOSFET ) 0065 microns
-Microarchitecture: Intel P6








Microprocessor "Quad Core"

is called 'quad-core' and has four cores on a single 'chip', which multiplied by billions the capacity of the first to hit the market 35 years ago.


Features:


* While the first transistor sold by Intel in 1971 had 2,300 transistors, the new has 2,000 million.
• In addition, each of the first transistors had a maximum clock speed (which takes to perform basic tasks, such as addition) of 740 kilohertz, while the new is of 2.66 gigahertz, nearly 3,600 times faster .
Intel • According to calculations, if the automobile had advanced as fast as the computer, a car would take far less than ten seconds to cross from coast to coast.
· Marketed under the name Core 2 Extreme quad-core (for the consumer market) and quad-core Xeon processor 530 (for servers) and with prices ranging from 455 to $ 1,172 (355 to 900 euros), this new generation of microprocessors also have the advantage that they consume almost 50% less power than their predecessors.
· "The observations of the great accelerator data give about 40 million times per second, so the 'quad-core' will be essential to manage about 15 billion gigabytes.


Tuesday, September 30, 2008

Optical Migraine Prism

My first Impala

Every year in early summer, Motoclub Impala Impala organized an excursion / concentration which together more than 100 bikes, all Montesa Impala. This year, in particular, 126 motorcycles.

Impala had to postpone scheduled for June 14 due to a strike in the Delivery will fuel at gas stations. Thus, the Impala was held on 20 September.

Notice that the second poster in the background colors vary, more autumnal ... ;-)




The Impala is a bike path all more or less together, with a couple of groupings. In total, counting the trip back home, did more than 300km.




Early morning we met at the top of Tibidabo. Will gradually appearing more and more Impalas to register, while the early bird breakfast.






putting the bikes are going well tidy ...










... to make the group photo ...




... and engines are started. A real delight for the senses. Being my first time, I assure you goose bumps.





In this video I go I ... jejejeje




(Incidentally, the videos and photos in this post are taken from the web of the motorcycle club, and here the artist left the camera ...)


We moved to the first grouping, and then you realize that we must go warily. Too many people, and more than a "quemadillo." He soon learns to go behind what has touched you, at your pace and distance leaving (most do not carry ;-)), brake lights ahead and forget, mostly because you can never go at your own pace. And in the same way, let it pass the "Quemao." In a country piss you off and take them out and quiet wheels.

The feeling is indescribable, to exit a corner and see that tape of Impalas, one after another, and all with the same gear engaged, so that the sound of the exhaust is unison. A joy.

Of course, at the beginning and the bikes cold, coughing, swallowing fans you smoke ...

Motoclub have hung in a video that illustrates very well what I explained so bad.



scrotumtightening, right?






In the last reunion we had the assistance of the legendary Josep M ª Busquets, a champion of Montjuich 24H with the 60 Impala.






a gentleman, he brought his own Impala 250 and to the Cromwell town with running, which still bears the scorpion painted.




the end, we group them (almost) everyone to eat (well, well) so that the end everyone will shake to return to its point of origin.

course, have an Impala and not go to the Impala should be punishable by law. Does anyone know any concentration anywhere in the world we can gather more than 100 motorcycles of the same make and model, and which is now more than 20 years that are not produced? I certainly do not.
And the Impala are not well ... what a shame bigger:-D

I for my part, I miss 2009.



Oops, I forgot. A couple of newspaper clippings of the event.




Impala 2008

Sunday, September 28, 2008

Funny Congrats Messages For Baby




Called RAM that you can access any location it randomly and quickly

What is RAM?

main memory or RAM (Random Access Memory, Random Access Memory) is where the computer stores the data that is used in the present moment. Storage is considered temporary because the data and programs remain there while the computer is turned on or is reset.
Physically, consist of a set of chips or chip modules normally connected to the motherboard. The memory chips are black rectangles soldiers often go in groups some chips with "pins" or contacts:



then submit the types of RAM and have evolved as each of them:



types of RAM MEMORY SIMM (Single In-line Memory Module)
ü exixte 2 TYPES OF ( 30 pins and 72 pins)

  • 30-pin SIMM MEMORY
    Coast Ø 30 contacts and 8 bits
    handled or used in computers
    Ø 386 and 486 came in modules 256kB, 1Mbit or tension
    5V supply is





  • MEMORIASIMM 72-pin Ø Coast
    72 contacts and drives to 32bits.
    or used on computers 484, 586, K6-II, K6-III, Celeron, Pentium, Pentium II. Ø
    4MByte capacity is up to 64MByte.
    Ø Work with a voltage of 5V.




  • MEMORY DIMM (Dual In-line Memory Module)
    Ø consists of 168 contacts and 64 bits.
    or available capacity to 512Mbytes 8Mbytes.
    Ø Work with a voltage of 3.3V and 5V.
    Ø With a memory bus speed that ranges from 66MHz to 133MHz.
    or begin to be used with the Pentium II and its use goes to the output of the Intel Pentium 4 processors and AMD Athlon XP



  • MEMORY DIMM DDR (DOUBLE DATA RATE) Double Data Rate
    Ø has 184 contacts in the same physical size of 168 contacts
    Ø Work with 2.5V and 1.8V voltage.
    Ø With a memory bus speed from 100MHz to 200MHz
    or begin to be used with the output of the Pentium 4 and XP
  • Thlon

  • MEMORY DDR2 DIMM 240-pin
    Ø has 240 pins and doubles the amount of data using 2 clocks. Ø
    speeds from 400MHz to 667MHz. Ø Ability to 1GByte
    . Ø
    have bus speeds of real memory from 100MHz to 266MHz.
    or consumption of these reports is between 0 and 1.8 volts.



  • DDR3 MEMORY DIMM has 240 pins Ø
    just the DDR3 DIMM.
    Ø Although not compatible with DDR2 memory. Ø
    memory bus speed from 800MHz effective 2000MHz. Ø
    consumption between 0 and 1.5 volts.
    Ø A maximum data transfer rate of 15.0GB / s.

CACHING
is used to facilitate a transfer even faster than the processor instructions and data that is used to improve process flow (how fast a system computer can do the job). Like RAM, the cache is an area of \u200b\u200bhigh-speed storage for program instructions and data, but shaved 10 times more than RAM. With only a fraction of the capacity of the RAM, the cache only contains instructions and data processor is likely to soon require
There are two types of cache memory: Memory
Ø L1 Cache L2 Cache
Ø

Conclusion:
ü As we have seen the emergence of electronic computers is fairly recent, and has had a rapid advance. So much so that today the competition between enterprises producing computers to rise to the emergence of new models with very short periods of time, which are sometimes of months. Causing an increase in processor speeds, storage capacity, speed of transfer of the buses, etc.. Ü
Currently the market is taking place again, because they have appeared very fast processors, which work speed of 1 GHz

Wednesday, July 9, 2008

Hutch Trickstar Modelnumbers



adjustment on

The Impala Sport carries a plate ignition magnetic breakers (platinum).

is based on the known principle of operation whereby a rotor with magnets on the perimeter rotates with the crankshaft of the engine. The rotor magnets rotate around a fixed plate holder coils (stator). The generated magnetic field induces current in these coils.

This stream will be utilized for two situations. A group of coils generate power for the electrical components of the bike (lights, horn, etc. ..). Another coil current to generate power plug, and make the spark jump between the electrodes. We refer here to the adjustment of this second system.

If we have the bike disassembled, begin by placing the stator in the crankcase, in that position that "suspect" was mounted at the beginning.




tighten the screws that hold the stator ...




We mounted magnetic plate by snapping it into the slot provided for that purpose.




With this set, we turn to hand the plate (rotor) until we get the maximum aperture of the points (closest point of the piston around TDC). That measure with a gauge opening them, which should be 0.4 mm




If the opening is not correct, with the plate in that position we loosen the screw holding the switch (platinum) and move slightly as appropriate, to open or close contacts of the switch over. Tighten the screw, turn to gauge and repeat the process as many times as needed until you have the required opening distance.




With maximum aperture of the contacts of the switch is properly adjusted, we proceed to determine the point of ignition advance, which should be 3.0 to 3.5 mm before TDC

bluntly, the points are separated just at the moment when the piston is at 3.0-3.5 mm before reaching the end of his career, that is, before peak. At the moment the contacts open, is when the spark jumps the spark plug.

To this end, a comparator, or caliper, or pencil, or stick ... seek piston TDC by turning the plate to right (clockwise rotation). When we find this point, we reverse the plate until the piston down from 3.0 to 3.5 mm. That is the exact point of ignition advance, and that's the exact point where the points should be opened.

To know whether open or not the points, the best way is to use a multimeter, looking for continuity between the switch and mobile leg mass motor. When there is no continuity, open the points.




Indeed, continuity is not interrupted (infinite resistance) as the mobile foot switch is connected to the condenser and low-voltage winding and ground it. If you can appreciate an increase in resistance. But to be sure, just before the switch is to disconnect the cable that connects it to the condenser and coil.



We turn the plate until we find the position which opens the switch (when we check the meter). We measure the magnitude of the piston is down. If this measure is higher than desired progress means that there is too much progress, and will have to delay the ignition, that is, remove the dish and turn the stator in the direction of clockwise. And vice versa.




--- slow down right-turn stator
--- Forward progress counterclockwise rotating stator




Once fully covered the advance, we put the connection Mobile Paw switch ...




... we make sure they are tightened the screws of the stator ...




... place of new steering wheel ...




... and we can consciously tighten the nut (thread inverted)






Checking on with strobe light.

The strobe light is a curious device that emits a flash of light at the right time when the spark at the plug. With the motor running, cause a series of flashes that "freeze" the movement appreciated by our eyes. We

a series of marks on the plate for the desired feed point, faced with another brand at a fixed point in the crankcase.




connected the unit to a 12V supply (eg battery) and insert the corresponding clip on the spark plug wire. This clip acts as a signal transducer. When it detects that the current passes spark plug wires, will light the lamp.

Start the engine and turn on the lamp, focusing the light toward the brands that we have in the wheel. The movement will be frozen just at the moment the spark, so we'll see if at that point just above the marks are properly carried faced.

A couple of sample videos. When the lamp is not in focus, we see nothing (motion = blur). When the lamp focus, we see the marks at the time of the spark (freezes the movement of the eye). Needless to say, in full sun will not see anything ...






If the marks are not aligned need to make the dish, adjust the position of the stator and rechecked.



And since we are the Lamp, play a little, and we can see the points through the window plate ...